OpenPKG Specs: comparison asterisk/misdn.conf

-:31165f1ec40e
+-1:000000000000
-;
-; chan_misdn sample config
-;
-; general section:
-;
-; for debugging and general setup, things that are not bound to port groups
-;
-;[general]
-;
-; Sets the Path to the misdn-init.conf (for nt_ptp mode checking)
-;
-;misdn_init=/etc/misdn-init.conf
-; set debugging flag:
-;   0 - No Debug
-;   1 - mISDN Messages and * - Messages, and * - State changes
-;   2 - Messages + Message specific Informations (e.g. bearer capability)
-;   3 - very Verbose, the above + lots of Driver specific infos
-;   4 - even more Verbose than 3
-;
-; default value: 0
-;
-;debug=0
-; set debugging file and flags for mISDNuser (NT-Stack)
-;
-; flags can be or'ed with the following values:
-;
-; DBGM_NET        0x00000001
-; DBGM_MSG        0x00000002
-; DBGM_FSM        0x00000004
-; DBGM_TEI        0x00000010
-; DBGM_L2         0x00000020
-; DBGM_L3         0x00000040
-; DBGM_L3DATA     0x00000080
-; DBGM_BC         0x00000100
-; DBGM_TONE       0x00000200
-; DBGM_BCDATA     0x00000400
-; DBGM_MAN        0x00001000
-; DBGM_APPL       0x00002000
-; DBGM_ISDN       0x00004000
-; DBGM_SOCK       0x00010000
-; DBGM_CONN       0x00020000
-; DBGM_CDATA      0x00040000
-; DBGM_DDATA      0x00080000
-; DBGM_SOUND      0x00100000
-; DBGM_SDATA      0x00200000
-; DBGM_TOPLEVEL   0x40000000
-; DBGM_ALL        0xffffffff
-;
-;ntdebugflags=0
-;ntdebugfile=/var/log/misdn-nt.log
-; some pbx systems do cut the L1 for some milliseconds, to avoid
-; dropping running calls, we can set this flag to yes and tell
-; mISDNuser not to drop the calls on L2_RELEASE
-;ntkeepcalls=no
-; the big trace
-;
-; default value: [not set]
-;
-;tracefile=/var/log/asterisk/misdn.log
-; set to yes if you want mISDN_dsp to bridge the calls in HW
-;
-; default value: yes
-;
-;bridging=no
-;
-; watches the L1s of every port. If one l1 is down it tries to
-; get it up. The timeout is given in seconds. with 0 as value it
-; does not watch the l1 at all
-;
-; default value: 0
-;
-; this option is only read at loading time of chan_misdn,
-; which means you need to unload and load chan_misdn to change the
-; value, an asterisk restart should do the trick
-;
-;l1watcher_timeout=0
-; stops dialtone after getting first digit on nt Port
-;
-; default value: yes
-;
-;stop_tone_after_first_digit=yes
-; whether to append overlapdialed Digits to Extension or not
-;
-; default value: yes
-;
-;append_digits2exten=yes
-;;; CRYPTION STUFF
-; Whether to look for dynamic crypting attempt
-;
-; default value: no
-;
-;dynamic_crypt=no
-; crypt_prefix, what is used for crypting Protocol
-;
-; default value: [not set]
-;
-;crypt_prefix=**
-; Keys for cryption, you reference them in the dialplan
-; later also in dynamic encr.
-;
-; default value: [not set]
-;
-;crypt_keys=test,muh
-; users sections:
-;
-; name your sections as you which but not "general" !
-; the sections are Groups, you can dial out in extensions.conf
-; with Dial(mISDN/g:extern/101) where extern is a section name,
-; chan_misdn tries every port in this section to find a
-; new free channel
-;
-; The default section is not a group section, it just contains config elements
-; which are inherited by group sections.
-;
-;[default]
-; define your default context here
-;
-; default value: default
-;
-;context=misdn
-; language
-;
-; default value: en
-;
-;language=en
-;
-; sets the musiconhold class
-;
-;musicclass=default
-;
-; Either if we should produce DTMF Tones ourselves
-;
-;senddtmf=yes
-;
-; If we should generate Ringing for chan_sip and others
-;
-;far_alerting=no
-;
-; here you can define which bearers should be allowed
-;
-;allowed_bearers=all
-; Prefixes for national and international, those are put before the
-; oad if an according dialplan is set by the other end.
-;
-; default values: nationalprefix      : 0
-;                 internationalprefix : 00
-;
-;nationalprefix=0
-;internationalprefix=00
-; set rx/tx gains between -8 and 8 to change the RX/TX Gain
-;
-; default values: rxgain: 0
-;                 txgain: 0
-;
-;rxgain=0
-;txgain=0
-; some telcos especially in NL seem to need this set to yes, also in
-; switzerland this seems to be important
-;
-; default value: no
-;
-;te_choose_channel=no
-;
-; This option defines, if chan_misdn should check the L1 on  a PMP
-; before making a group call on it. The L1 may go down for PMP Ports
-; so we might need this.
-; But be aware! a broken or plugged off cable might be used for a group call
-; as well, since chan_misdn has no chance to distinguish if the L1 is down
-; because of a lost Link or because the Provider shut it down...
-;
-; default: no
-;
-;pmp_l1_check=no
-;
-; in PMP this option defines which cause should be sent out to
-; the 3. caller. chan_misdn does not support callwaiting on TE
-; PMP side. This allows to modify the RELEASE_COMPLETE cause
-; at least.
-;
-;reject_cause=16
-;
-; Send Setup_Acknowledge on incoming calls anyway (instead of PROCEEDING),
-; this requests additional Infos, so we can waitfordigits
-; without much issues. This works only for PTP Ports
-;
-; default value: no
-;
-;need_more_infos=no
-;
-; set this to yes if you want to disconnect calls when a timeout occurs
-; for example during the overlapdial phase
-;
-;nttimeout=no
-; set the method to use for channel selection:
-;   standard    - always choose the first free channel with the lowest number
-;   round_robin - use the round robin algorithm to select a channel. use this
-;                 if you want to balance your load.
-;
-; default value: standard
-;
-;method=standard
-; specify if chan_misdn should collect digits before going into the
-; dialplan, you can choose yes=4 Seconds, no, or specify the amount
-; of seconds you need;
-;
-;overlapdial=yes
-;
-; dialplan means Type Of Number in ISDN Terms (for outgoing calls)
-;
-; there are different types of the dialplan:
-;
-; dialplan -> outgoing Number
-; localdialplan -> callerid
-; cpndialplan -> connected party number
-;
-; dialplan options:
-;
-; 0 - unknown
-; 1 - International
-; 2 - National
-; 4 - Subscriber
-;
-; This setting is used for outgoing calls
-;
-; default value: 0
-;
-;dialplan=0
-;localdialplan=0
-;cpndialplan=0
-;
-; turn this to no if you don't mind correct handling of Progress Indicators
-;
-;early_bconnect=yes
-;
-; turn this on if you like to send Tone Indications to a Incoming
-; isdn channel on a TE Port. Rarely used, only if the Telco allows
-; you to send indications by yourself, normally the Telco sends the
-; indications to the remote party.
-;
-; default: no
-;
-;incoming_early_audio=no
-; uncomment the following to get into s extension at extension conf
-; there you can use DigitTimeout if you can't or don't want to use
-; isdn overlap dial.
-; note: This will jump into the s exten for every exten!
-;
-; default value: no
-;
-;always_immediate=no
-;
-; set this to yes if you want to generate your own dialtone
-; with always_immediate=yes, else chan_misdn generates the dialtone
-;
-; default value: no
-;
-;nodialtone=no
-; uncomment the following if you want callers which called exactly the
-; base number (so no extension is set) jump to the s extension.
-; if the user dials something more it jumps to the correct extension
-; instead
-;
-; default value: no
-;
-;immediate=no
-; uncomment the following to have hold and retrieve support
-;
-; default value: no
-;
-;hold_allowed=yes
-; Pickup and Callgroup
-;
-; default values: not set = 0
-; range: 0-63
-;
-;callgroup=1
-;pickupgroup=1
-;
-; these are the exact isdn screening and presentation indicators
-; if -1 is given for both values the presentation indicators are used
-; from asterisks SetCallerPres application.
-; s=0, p=0 -> callerid presented not screened
-; s=1, p=1 -> callerid presented but screened (the remote end does not see it!)
-;
-; default values s=-1, p=-1
-;presentation=-1
-;screen=-1
-; this enables echocancellation, with the given number of taps
-; be aware, move this setting only to outgoing portgroups!
-; A value of zero turns echocancellation off.
-;
-; possible values are: 0,32,64,128,256,yes(=128),no(=0)
-;
-; default value: no
-;
-;echocancel=no
-; Set this to no to disable echotraining. You can enter a number > 10
-; the value is a multiple of 0.125 ms.
-;
-; default value: no
-; yes = 2000
-; no = 0
-;
-;echotraining=no
-;
-; chan_misdns jitterbuffer, default 4000
-;
-;jitterbuffer=4000
-;
-; change this threshold to enable dejitter functionality
-;
-;jitterbuffer_upper_threshold=0
-;
-; change this to yes, if you want to bridge a mISDN data channel to
-; another channel type or to an application.
-;
-;hdlc=no
-;
-; defines the maximum amount of incoming calls per port for
-; this group. Calls which exceed the maximum will be marked with
-; the channel variable MAX_OVERFLOW. It will contain the amount of
-; overflowed calls
-;
-;max_incoming=-1
-;
-; defines the maximum amount of outgoing calls per port for this group
-; exceeding calls will be rejected
-;
-;max_outgoing=-1
-;[intern]
-; define your ports, e.g. 1,2 (depends on mISDN-driver loading order)
-;ports=1,2
-; context where to go to when incoming Call on one of the above ports
-;context=Intern
-;[internPP]
-;
-; adding the postfix 'ptp' to a port number is obsolete now, chan_misdn
-; parses /etc/misdn-init.conf and sets the ptp mode to the corresponding
-; configs. For backwards compatibility you can still set ptp here.
-;
-;ports=3
-;[first_extern]
-; again port defs
-;ports=4
-; again a context for incoming calls
-;context=Extern1
-; msns for te ports, listen on those numbers on the above ports, and
-; indicate the incoming calls to asterisk
-; here you can give a comma separated list or simply an '*' for
-; any msn.
-;msns=*
-; here an example with given msns
-;[second_extern]
-;ports=5
-;context=Extern2
-;callerid=15
-;msns=102,144,101,104

OpenPKG Specs / file comparison

comparison: asterisk/misdn.conf

asterisk/misdn.conf