1.1 --- /dev/null Thu Jan 01 00:00:00 1970 +0000
1.2 +++ b/asterisk/extensions.conf Mon Apr 27 12:19:05 2009 +0200
1.3 @@ -0,0 +1,614 @@
1.4 +; extensions.conf - the Asterisk dial plan
1.5 +;
1.6 +; Static extension configuration file, used by
1.7 +; the pbx_config module. This is where you configure all your
1.8 +; inbound and outbound calls in Asterisk.
1.9 +;
1.10 +; This configuration file is reloaded
1.11 +; - With the "dialplan reload" command in the CLI
1.12 +; - With the "reload" command (that reloads everything) in the CLI
1.13 +
1.14 +;
1.15 +; The "General" category is for certain variables.
1.16 +;
1.17 +;[general]
1.18 +;
1.19 +; If static is set to no, or omitted, then the pbx_config will rewrite
1.20 +; this file when extensions are modified. Remember that all comments
1.21 +; made in the file will be lost when that happens.
1.22 +;
1.23 +; XXX Not yet implemented XXX
1.24 +;
1.25 +;static=yes
1.26 +;
1.27 +; if static=yes and writeprotect=no, you can save dialplan by
1.28 +; CLI command "dialplan save" too
1.29 +;
1.30 +;writeprotect=no
1.31 +;
1.32 +; If autofallthrough is set, then if an extension runs out of
1.33 +; things to do, it will terminate the call with BUSY, CONGESTION
1.34 +; or HANGUP depending on Asterisk's best guess. This is the default.
1.35 +;
1.36 +; If autofallthrough is not set, then if an extension runs out of
1.37 +; things to do, Asterisk will wait for a new extension to be dialed
1.38 +; (this is the original behavior of Asterisk 1.0 and earlier).
1.39 +;
1.40 +;autofallthrough=no
1.41 +;
1.42 +; If clearglobalvars is set, global variables will be cleared
1.43 +; and reparsed on an extensions reload, or Asterisk reload.
1.44 +;
1.45 +; If clearglobalvars is not set, then global variables will persist
1.46 +; through reloads, and even if deleted from the extensions.conf or
1.47 +; one of its included files, will remain set to the previous value.
1.48 +;
1.49 +; NOTE: A complication sets in, if you put your global variables into
1.50 +; the AEL file, instead of the extensions.conf file. With clearglobalvars
1.51 +; set, a "reload" will often leave the globals vars cleared, because it
1.52 +; is not unusual to have extensions.conf (which will have no globals)
1.53 +; load after the extensions.ael file (where the global vars are stored).
1.54 +; So, with "reload" in this particular situation, first the AEL file will
1.55 +; clear and then set all the global vars, then, later, when the extensions.conf
1.56 +; file is loaded, the global vars are all cleared, and then not set, because
1.57 +; they are not stored in the extensions.conf file.
1.58 +;
1.59 +;clearglobalvars=no
1.60 +;
1.61 +; If priorityjumping is set to 'yes', then applications that support
1.62 +; 'jumping' to a different priority based on the result of their operations
1.63 +; will do so (this is backwards compatible behavior with pre-1.2 releases
1.64 +; of Asterisk). Individual applications can also be requested to do this
1.65 +; by passing a 'j' option in their arguments.
1.66 +;
1.67 +;priorityjumping=yes
1.68 +;
1.69 +; User context is where entries from users.conf are registered. The
1.70 +; default value is 'default'
1.71 +;
1.72 +;userscontext=default
1.73 +;
1.74 +; You can include other config files, use the #include command
1.75 +; (without the ';'). Note that this is different from the "include" command
1.76 +; that includes contexts within other contexts. The #include command works
1.77 +; in all asterisk configuration files.
1.78 +;#include "filename.conf"
1.79 +
1.80 +; The "Globals" category contains global variables that can be referenced
1.81 +; in the dialplan with the GLOBAL dialplan function:
1.82 +; ${GLOBAL(VARIABLE)}
1.83 +; ${${GLOBAL(VARIABLE)}} or ${text${GLOBAL(VARIABLE)}} or any hybrid
1.84 +; Unix/Linux environmental variables can be reached with the ENV dialplan
1.85 +; function: ${ENV(VARIABLE)}
1.86 +;
1.87 +;[globals]
1.88 +;CONSOLE=Console/dsp ; Console interface for demo
1.89 +;CONSOLE=Zap/1
1.90 +;CONSOLE=Phone/phone0
1.91 +;IAXINFO=guest ; IAXtel username/password
1.92 +;IAXINFO=myuser:mypass
1.93 +;TRUNK=Zap/G2 ; Trunk interface
1.94 +;
1.95 +; Note the 'G2' in the TRUNK variable above. It specifies which group (defined
1.96 +; in zapata.conf) to dial, i.e. group 2, and how to choose a channel to use in
1.97 +; the specified group. The four possible options are:
1.98 +;
1.99 +; g: select the lowest-numbered non-busy Zap channel
1.100 +; (aka. ascending sequential hunt group).
1.101 +; G: select the highest-numbered non-busy Zap channel
1.102 +; (aka. descending sequential hunt group).
1.103 +; r: use a round-robin search, starting at the next highest channel than last
1.104 +; time (aka. ascending rotary hunt group).
1.105 +; R: use a round-robin search, starting at the next lowest channel than last
1.106 +; time (aka. descending rotary hunt group).
1.107 +;
1.108 +;TRUNKMSD=1 ; MSD digits to strip (usually 1 or 0)
1.109 +;TRUNK=IAX2/user:pass@provider
1.110 +
1.111 +;
1.112 +; Any category other than "General" and "Globals" represent
1.113 +; extension contexts, which are collections of extensions.
1.114 +;
1.115 +; Extension names may be numbers, letters, or combinations
1.116 +; thereof. If an extension name is prefixed by a '_'
1.117 +; character, it is interpreted as a pattern rather than a
1.118 +; literal. In patterns, some characters have special meanings:
1.119 +;
1.120 +; X - any digit from 0-9
1.121 +; Z - any digit from 1-9
1.122 +; N - any digit from 2-9
1.123 +; [1235-9] - any digit in the brackets (in this example, 1,2,3,5,6,7,8,9)
1.124 +; . - wildcard, matches anything remaining (e.g. _9011. matches
1.125 +; anything starting with 9011 excluding 9011 itself)
1.126 +; ! - wildcard, causes the matching process to complete as soon as
1.127 +; it can unambiguously determine that no other matches are possible
1.128 +;
1.129 +; For example the extension _NXXXXXX would match normal 7 digit dialings,
1.130 +; while _1NXXNXXXXXX would represent an area code plus phone number
1.131 +; preceded by a one.
1.132 +;
1.133 +; Each step of an extension is ordered by priority, which must
1.134 +; always start with 1 to be considered a valid extension. The priority
1.135 +; "next" or "n" means the previous priority plus one, regardless of whether
1.136 +; the previous priority was associated with the current extension or not.
1.137 +; The priority "same" or "s" means the same as the previously specified
1.138 +; priority, again regardless of whether the previous entry was for the
1.139 +; same extension. Priorities may be immediately followed by a plus sign
1.140 +; and another integer to add that amount (most useful with 's' or 'n').
1.141 +; Priorities may then also have an alias, or label, in
1.142 +; parenthesis after their name which can be used in goto situations
1.143 +;
1.144 +; Contexts contain several lines, one for each step of each
1.145 +; extension, which can take one of two forms as listed below,
1.146 +; with the first form being preferred.
1.147 +;
1.148 +;[context]
1.149 +;exten => someexten,{priority|label{+|-}offset}[(alias)],application(arg1,arg2,...)
1.150 +;exten => someexten,{priority|label{+|-}offset}[(alias)],application,arg1|arg2...
1.151 +;
1.152 +; Included Contexts
1.153 +;
1.154 +; One may include another context in the current one as well, optionally with a
1.155 +; date and time. Included contexts are included in the order
1.156 +; they are listed.
1.157 +; The reason a context would include other contexts is for their
1.158 +; extensions.
1.159 +; The algorithm to find an extension is recursive, and works in this
1.160 +; fashion:
1.161 +; first, given a stack on which to store context references,
1.162 +; push the context to find the extension onto the stack...
1.163 +; a) Try to find a matching extension in the context at the top of
1.164 +; the stack, and, if found, begin executing the priorities
1.165 +; there in sequence.
1.166 +; b) If not found, Search the switches, if any declared, in
1.167 +; sequence.
1.168 +; c) If still not found, for each include, push that context onto
1.169 +; the top of the context stack, and recurse to a).
1.170 +; d) If still not found, pop the entry from the top of the stack;
1.171 +; if the stack is empty, the search has failed. If it's not,
1.172 +; continue with the next context in c).
1.173 +; This is a depth-first traversal, and stops with the first context
1.174 +; that provides a matching extension. As usual, if more than one
1.175 +; pattern in a context will match, the 'best' match will win.
1.176 +; Please note that that extensions found in an included context are
1.177 +; treated as if they were in the context from which the search began.
1.178 +; The PBX's notion of the "current context" is not changed.
1.179 +; Please note that in a context, it does not matter where an include
1.180 +; directive occurs. Whether at the top, or near the bottom, the effect
1.181 +; will be the same. The only thing that matters is that if there is
1.182 +; more than one include directive, they will be searched for extensions
1.183 +; in order, first to last.
1.184 +; Also please note that pattern matches (like _9XX) are not treated
1.185 +; any differently than exact matches (like 987). Also note that the
1.186 +; order of extensions in a context have no affect on the outcome.
1.187 +;
1.188 +; Timing list for includes is
1.189 +;
1.190 +; <time range>|<days of week>|<days of month>|<months>
1.191 +;
1.192 +; Note that ranges may be specified to wrap around the ends. Also, minutes are
1.193 +; fine-grained only down to the closest even minute.
1.194 +;
1.195 +;include => daytime|9:00-17:00|mon-fri|*|*
1.196 +;include => weekend|*|sat-sun|*|*
1.197 +;include => weeknights|17:02-8:58|mon-fri|*|*
1.198 +;
1.199 +; ignorepat can be used to instruct drivers to not cancel dialtone upon
1.200 +; receipt of a particular pattern. The most commonly used example is
1.201 +; of course '9' like this:
1.202 +;
1.203 +;ignorepat => 9
1.204 +;
1.205 +; so that dialtone remains even after dialing a 9.
1.206 +;
1.207 +
1.208 +;
1.209 +; Sample entries for extensions.conf
1.210 +;
1.211 +;
1.212 +;[dundi-e164-canonical]
1.213 +;
1.214 +; List canonical entries here
1.215 +;
1.216 +;exten => 12564286000,1,Macro(stdexten,6000,IAX2/foo)
1.217 +;exten => _125642860XX,1,Dial(IAX2/otherbox/${EXTEN:7})
1.218 +
1.219 +;[dundi-e164-customers]
1.220 +;
1.221 +; If you are an ITSP or Reseller, list your customers here.
1.222 +;
1.223 +;exten => _12564286000,1,Dial(SIP/customer1)
1.224 +;exten => _12564286001,1,Dial(IAX2/customer2)
1.225 +
1.226 +;[dundi-e164-via-pstn]
1.227 +;
1.228 +; If you are freely delivering calls to the PSTN, list them here
1.229 +;
1.230 +;exten => _1256428XXXX,1,Dial(Zap/G2/${EXTEN:7}) ; Expose all of 256-428
1.231 +;exten => _1256325XXXX,1,Dial(Zap/G2/${EXTEN:7}) ; Ditto for 256-325
1.232 +
1.233 +;[dundi-e164-local]
1.234 +;
1.235 +; Context to put your dundi IAX2 or SIP user in for
1.236 +; full access
1.237 +;
1.238 +;include => dundi-e164-canonical
1.239 +;include => dundi-e164-customers
1.240 +;include => dundi-e164-via-pstn
1.241 +
1.242 +;[dundi-e164-switch]
1.243 +;
1.244 +; Just a wrapper for the switch
1.245 +;
1.246 +;switch => DUNDi/e164
1.247 +
1.248 +;[dundi-e164-lookup]
1.249 +;
1.250 +; Locally to lookup, try looking for a local E.164 solution
1.251 +; then try DUNDi if we don't have one.
1.252 +;
1.253 +;include => dundi-e164-local
1.254 +;include => dundi-e164-switch
1.255 +;
1.256 +; DUNDi can also be implemented as a Macro instead of using
1.257 +; the Local channel driver.
1.258 +;
1.259 +;[macro-dundi-e164]
1.260 +;
1.261 +; ARG1 is the extension to Dial
1.262 +;
1.263 +; Extension "s" is not a wildcard extension that matches "anything".
1.264 +; In macros, it is the start extension. In most other cases,
1.265 +; you have to goto "s" to execute that extension.
1.266 +;
1.267 +; For wildcard matches, see above - all pattern matches start with
1.268 +; an underscore.
1.269 +;exten => s,1,Goto(${ARG1},1)
1.270 +;include => dundi-e164-lookup
1.271 +
1.272 +;
1.273 +; Here are the entries you need to participate in the IAXTEL
1.274 +; call routing system. Most IAXTEL numbers begin with 1-700, but
1.275 +; there are exceptions. For more information, and to sign
1.276 +; up, please go to www.gnophone.com or www.iaxtel.com
1.277 +;
1.278 +;[iaxtel700]
1.279 +;exten => _91700XXXXXXX,1,Dial(IAX2/${GLOBAL(IAXINFO)}@iaxtel.com/${EXTEN:1}@iaxtel)
1.280 +
1.281 +;
1.282 +; The SWITCH statement permits a server to share the dialplan with
1.283 +; another server. Use with care: Reciprocal switch statements are not
1.284 +; allowed (e.g. both A -> B and B -> A), and the switched server needs
1.285 +; to be on-line or else dialing can be severly delayed.
1.286 +;
1.287 +;[iaxprovider]
1.288 +;switch => IAX2/user:[key]@myserver/mycontext
1.289 +
1.290 +;[trunkint]
1.291 +;
1.292 +; International long distance through trunk
1.293 +;
1.294 +;exten => _9011.,1,Macro(dundi-e164,${EXTEN:4})
1.295 +;exten => _9011.,n,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}})
1.296 +
1.297 +;[trunkld]
1.298 +;
1.299 +; Long distance context accessed through trunk
1.300 +;
1.301 +;exten => _91NXXNXXXXXX,1,Macro(dundi-e164,${EXTEN:1})
1.302 +;exten => _91NXXNXXXXXX,n,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}})
1.303 +
1.304 +;[trunklocal]
1.305 +;
1.306 +; Local seven-digit dialing accessed through trunk interface
1.307 +;
1.308 +;exten => _9NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}})
1.309 +
1.310 +;[trunktollfree]
1.311 +;
1.312 +; Long distance context accessed through trunk interface
1.313 +;
1.314 +;exten => _91800NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}})
1.315 +;exten => _91888NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}})
1.316 +;exten => _91877NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}})
1.317 +;exten => _91866NXXXXXX,1,Dial(${GLOBAL(TRUNK)}/${EXTEN:${GLOBAL(TRUNKMSD)}})
1.318 +
1.319 +;[international]
1.320 +;
1.321 +; Master context for international long distance
1.322 +;
1.323 +;ignorepat => 9
1.324 +;include => longdistance
1.325 +;include => trunkint
1.326 +
1.327 +;[longdistance]
1.328 +;
1.329 +; Master context for long distance
1.330 +;
1.331 +;ignorepat => 9
1.332 +;include => local
1.333 +;include => trunkld
1.334 +
1.335 +;[local]
1.336 +;
1.337 +; Master context for local, toll-free, and iaxtel calls only
1.338 +;
1.339 +;ignorepat => 9
1.340 +;include => default
1.341 +;include => trunklocal
1.342 +;include => iaxtel700
1.343 +;include => trunktollfree
1.344 +;include => iaxprovider
1.345 +
1.346 +;Include parkedcalls (or the context you define in features conf)
1.347 +;to enable call parking.
1.348 +;include => parkedcalls
1.349 +;
1.350 +; You can use an alternative switch type as well, to resolve
1.351 +; extensions that are not known here, for example with remote
1.352 +; IAX switching you transparently get access to the remote
1.353 +; Asterisk PBX
1.354 +;
1.355 +; switch => IAX2/user:password@bigserver/local
1.356 +;
1.357 +; An "lswitch" is like a switch but is literal, in that
1.358 +; variable substitution is not performed at load time
1.359 +; but is passed to the switch directly (presumably to
1.360 +; be substituted in the switch routine itself)
1.361 +;
1.362 +; lswitch => Loopback/12${EXTEN}@othercontext
1.363 +;
1.364 +; An "eswitch" is like a switch but the evaluation of
1.365 +; variable substitution is performed at runtime before
1.366 +; being passed to the switch routine.
1.367 +;
1.368 +; eswitch => IAX2/context@${CURSERVER}
1.369 +
1.370 +;[macro-trunkdial]
1.371 +;
1.372 +; Standard trunk dial macro (hangs up on a dialstatus that should
1.373 +; terminate call)
1.374 +; ${ARG1} - What to dial
1.375 +;
1.376 +;exten => s,1,Dial(${ARG1})
1.377 +;exten => s,n,Goto(s-${DIALSTATUS},1)
1.378 +;exten => s-NOANSWER,1,Hangup
1.379 +;exten => s-BUSY,1,Hangup
1.380 +;exten => _s-.,1,NoOp
1.381 +
1.382 +;[macro-stdexten];
1.383 +;
1.384 +; Standard extension macro:
1.385 +; ${ARG1} - Extension (we could have used ${MACRO_EXTEN} here as well
1.386 +; ${ARG2} - Device(s) to ring
1.387 +;
1.388 +;exten => s,1,Dial(${ARG2},20) ; Ring the interface, 20 seconds maximum
1.389 +;exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER)
1.390 +
1.391 +;exten => s-NOANSWER,1,Voicemail(${ARG1},u) ; If unavailable, send to voicemail w/ unavail announce
1.392 +;exten => s-NOANSWER,2,Goto(default,s,1) ; If they press #, return to start
1.393 +
1.394 +;exten => s-BUSY,1,Voicemail(${ARG1},b) ; If busy, send to voicemail w/ busy announce
1.395 +;exten => s-BUSY,2,Goto(default,s,1) ; If they press #, return to start
1.396 +
1.397 +;exten => _s-.,1,Goto(s-NOANSWER,1) ; Treat anything else as no answer
1.398 +
1.399 +;exten => a,1,VoicemailMain(${ARG1}) ; If they press *, send the user into VoicemailMain
1.400 +
1.401 +;[macro-stdPrivacyexten];
1.402 +;
1.403 +; Standard extension macro:
1.404 +; ${ARG1} - Extension (we could have used ${MACRO_EXTEN} here as well
1.405 +; ${ARG2} - Device(s) to ring
1.406 +; ${ARG3} - Optional DONTCALL context name to jump to (assumes the s,1 extension-priority)
1.407 +; ${ARG4} - Optional TORTURE context name to jump to (assumes the s,1 extension-priority)`
1.408 +;
1.409 +;exten => s,1,Dial(${ARG2},20|p) ; Ring the interface, 20 seconds maximum, call screening
1.410 + ; option (or use P for databased call screening)
1.411 +;exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER)
1.412 +
1.413 +;exten => s-NOANSWER,1,Voicemail(${ARG1},u) ; If unavailable, send to voicemail w/ unavail announce
1.414 +;exten => s-NOANSWER,2,Goto(default,s,1) ; If they press #, return to start
1.415 +
1.416 +;exten => s-BUSY,1,Voicemail(${ARG1},b) ; If busy, send to voicemail w/ busy announce
1.417 +;exten => s-BUSY,2,Goto(default,s,1) ; If they press #, return to start
1.418 +
1.419 +;exten => s-DONTCALL,1,Goto(${ARG3},s,1) ; Callee chose to send this call to a polite "Don't call again" script.
1.420 +
1.421 +;exten => s-TORTURE,1,Goto(${ARG4},s,1) ; Callee chose to send this call to a telemarketer torture script.
1.422 +
1.423 +;exten => _s-.,1,Goto(s-NOANSWER,1) ; Treat anything else as no answer
1.424 +
1.425 +;exten => a,1,VoicemailMain(${ARG1}) ; If they press *, send the user into VoicemailMain
1.426 +
1.427 +;[macro-page];
1.428 +;
1.429 +; Paging macro:
1.430 +;
1.431 +; Check to see if SIP device is in use and DO NOT PAGE if they are
1.432 +;
1.433 +; ${ARG1} - Device to page
1.434 +
1.435 +;exten => s,1,ChanIsAvail(${ARG1}|js) ; j is for Jump and s is for ANY call
1.436 +;exten => s,n,GoToIf([${AVAILSTATUS} = "1"]?autoanswer:fail)
1.437 +;exten => s,n(autoanswer),Set(_ALERT_INFO="RA") ; This is for the PolyComs
1.438 +;exten => s,n,SIPAddHeader(Call-Info: Answer-After=0) ; This is for the Grandstream, Snoms, and Others
1.439 +;exten => s,n,NoOp() ; Add others here and Post on the Wiki!!!!
1.440 +;exten => s,n,Dial(${ARG1}||)
1.441 +;exten => s,n(fail),Hangup
1.442 +
1.443 +
1.444 +;[demo]
1.445 +;
1.446 +; We start with what to do when a call first comes in.
1.447 +;
1.448 +;exten => s,1,Wait(1) ; Wait a second, just for fun
1.449 +;exten => s,n,Answer ; Answer the line
1.450 +;exten => s,n,Set(TIMEOUT(digit)=5) ; Set Digit Timeout to 5 seconds
1.451 +;exten => s,n,Set(TIMEOUT(response)=10) ; Set Response Timeout to 10 seconds
1.452 +;exten => s,n(restart),BackGround(demo-congrats) ; Play a congratulatory message
1.453 +;exten => s,n(instruct),BackGround(demo-instruct) ; Play some instructions
1.454 +;exten => s,n,WaitExten ; Wait for an extension to be dialed.
1.455 +
1.456 +;exten => 2,1,BackGround(demo-moreinfo) ; Give some more information.
1.457 +;exten => 2,n,Goto(s,instruct)
1.458 +
1.459 +;exten => 3,1,Set(LANGUAGE()=fr) ; Set language to french
1.460 +;exten => 3,n,Goto(s,restart) ; Start with the congratulations
1.461 +
1.462 +;exten => 1000,1,Goto(default,s,1)
1.463 +;
1.464 +; We also create an example user, 1234, who is on the console and has
1.465 +; voicemail, etc.
1.466 +;
1.467 +;exten => 1234,1,Playback(transfer,skip) ; "Please hold while..."
1.468 + ; (but skip if channel is not up)
1.469 +;exten => 1234,n,Macro(stdexten,1234,${GLOBAL(CONSOLE)})
1.470 +
1.471 +;exten => 1235,1,Voicemail(1234,u) ; Right to voicemail
1.472 +
1.473 +;exten => 1236,1,Dial(Console/dsp) ; Ring forever
1.474 +;exten => 1236,n,Voicemail(1234,b) ; Unless busy
1.475 +
1.476 +;
1.477 +; # for when they're done with the demo
1.478 +;
1.479 +;exten => #,1,Playback(demo-thanks) ; "Thanks for trying the demo"
1.480 +;exten => #,n,Hangup ; Hang them up.
1.481 +
1.482 +;
1.483 +; A timeout and "invalid extension rule"
1.484 +;
1.485 +;exten => t,1,Goto(#,1) ; If they take too long, give up
1.486 +;exten => i,1,Playback(invalid) ; "That's not valid, try again"
1.487 +
1.488 +;
1.489 +; Create an extension, 500, for dialing the
1.490 +; Asterisk demo.
1.491 +;
1.492 +;exten => 500,1,Playback(demo-abouttotry); Let them know what's going on
1.493 +;exten => 500,n,Dial(IAX2/guest@pbx.digium.com/s@default) ; Call the Asterisk demo
1.494 +;exten => 500,n,Playback(demo-nogo) ; Couldn't connect to the demo site
1.495 +;exten => 500,n,Goto(s,6) ; Return to the start over message.
1.496 +
1.497 +;
1.498 +; Create an extension, 600, for evaluating echo latency.
1.499 +;
1.500 +;exten => 600,1,Playback(demo-echotest) ; Let them know what's going on
1.501 +;exten => 600,n,Echo ; Do the echo test
1.502 +;exten => 600,n,Playback(demo-echodone) ; Let them know it's over
1.503 +;exten => 600,n,Goto(s,6) ; Start over
1.504 +
1.505 +;
1.506 +; You can use the Macro Page to intercom a individual user
1.507 +;exten => 76245,1,Macro(page,SIP/Grandstream1)
1.508 +; or if your peernames are the same as extensions
1.509 +;exten => _7XXX,1,Macro(page,SIP/${EXTEN})
1.510 +;
1.511 +;
1.512 +; System Wide Page at extension 7999
1.513 +;
1.514 +;exten => 7999,1,Set(TIMEOUT(absolute)=60)
1.515 +;exten => 7999,2,Page(Local/Grandstream1@page&Local/Xlite1@page&Local/1234@page/n|d)
1.516 +
1.517 +; Give voicemail at extension 8500
1.518 +;
1.519 +;exten => 8500,1,VoicemailMain
1.520 +;exten => 8500,n,Goto(s,6)
1.521 +;
1.522 +; Here's what a phone entry would look like (IXJ for example)
1.523 +;
1.524 +;exten => 1265,1,Dial(Phone/phone0,15)
1.525 +;exten => 1265,n,Goto(s,5)
1.526 +
1.527 +;
1.528 +; The page context calls up the page macro that sets variables needed for auto-answer
1.529 +; It is in is own context to make calling it from the Page() application as simple as
1.530 +; Local/{peername}@page
1.531 +;
1.532 +;[page]
1.533 +;exten => _X.,1,Macro(page,SIP/${EXTEN})
1.534 +
1.535 +;[mainmenu]
1.536 +;
1.537 +; Example "main menu" context with submenu
1.538 +;
1.539 +;exten => s,1,Answer
1.540 +;exten => s,n,Background(thanks) ; "Thanks for calling press 1 for sales, 2 for support, ..."
1.541 +;exten => s,n,WaitExten
1.542 +;exten => 1,1,Goto(submenu,s,1)
1.543 +;exten => 2,1,Hangup
1.544 +;include => default
1.545 +;
1.546 +;[submenu]
1.547 +;exten => s,1,Ringing ; Make them comfortable with 2 seconds of ringback
1.548 +;exten => s,n,Wait,2
1.549 +;exten => s,n,Background(submenuopts) ; "Thanks for calling the sales department. Press 1 for steve, 2 for..."
1.550 +;exten => s,n,WaitExten
1.551 +;exten => 1,1,Goto(default,steve,1)
1.552 +;exten => 2,1,Goto(default,mark,2)
1.553 +
1.554 +;[default]
1.555 +;
1.556 +; By default we include the demo. In a production system, you
1.557 +; probably don't want to have the demo there.
1.558 +;
1.559 +;include => demo
1.560 +
1.561 +;
1.562 +; An extension like the one below can be used for FWD, Nikotel, sipgate etc.
1.563 +; Note that you must have a [sipprovider] section in sip.conf
1.564 +;
1.565 +;exten => _41X.,1,Dial(SIP/${EXTEN:2}@sipprovider,,r)
1.566 +
1.567 +; Real extensions would go here. Generally you want real extensions to be
1.568 +; 4 or 5 digits long (although there is no such requirement) and start with a
1.569 +; single digit that is fairly large (like 6 or 7) so that you have plenty of
1.570 +; room to overlap extensions and menu options without conflict. You can alias
1.571 +; them with names, too, and use global variables
1.572 +
1.573 +;exten => 6245,hint,SIP/Grandstream1&SIP/Xlite1,Joe Schmoe ; Channel hints for presence
1.574 +;exten => 6245,1,Dial(SIP/Grandstream1,20,rt) ; permit transfer
1.575 +;exten => 6245,n(dial),Dial(${HINT},20,rtT) ; Use hint as listed
1.576 +;exten => 6245,n,Voicemail(6245,u) ; Voicemail (unavailable)
1.577 +;exten => 6245,s+1,Hangup ; s+1, same as n
1.578 +;exten => 6245,dial+101,Voicemail(6245,b) ; Voicemail (busy)
1.579 +;exten => 6361,1,Dial(IAX2/JaneDoe,,rm) ; ring without time limit
1.580 +;exten => 6389,1,Dial(MGCP/aaln/1@192.168.0.14)
1.581 +;exten => 6390,1,Dial(JINGLE/caller/callee) ; Dial via jingle using labels
1.582 +;exten => 6391,1,Dial(JINGLE/asterisk@digium.com/mogorman@astjab.org) ;Dial via jingle using asterisk as the transport and calling mogorman.
1.583 +;exten => 6394,1,Dial(Local/6275/n) ; this will dial ${MARK}
1.584 +
1.585 +;exten => 6275,1,Macro(stdexten,6275,${MARK}) ; assuming ${MARK} is something like Zap/2
1.586 +;exten => mark,1,Goto(6275|1) ; alias mark to 6275
1.587 +;exten => 6536,1,Macro(stdexten,6236,${WIL}) ; Ditto for wil
1.588 +;exten => wil,1,Goto(6236|1)
1.589 +
1.590 +;If you want to subscribe to the status of a parking space, this is
1.591 +;how you do it. Subscribe to extension 6600 in sip, and you will see
1.592 +;the status of the first parking lot with this extensions' help
1.593 +;exten => 6600,hint,park:701@parkedcalls
1.594 +;exten => 6600,1,noop
1.595 +;
1.596 +; Some other handy things are an extension for checking voicemail via
1.597 +; voicemailmain
1.598 +;
1.599 +;exten => 8500,1,VoicemailMain
1.600 +;exten => 8500,n,Hangup
1.601 +;
1.602 +; Or a conference room (you'll need to edit meetme.conf to enable this room)
1.603 +;
1.604 +;exten => 8600,1,Meetme(1234)
1.605 +;
1.606 +; Or playing an announcement to the called party, as soon it answers
1.607 +;
1.608 +;exten = 8700,1,Dial(${MARK},30,A(/path/to/my/announcemsg))
1.609 +;
1.610 +; For more information on applications, just type "core show applications" at your
1.611 +; friendly Asterisk CLI prompt.
1.612 +;
1.613 +; "core show application <command>" will show details of how you
1.614 +; use that particular application in this file, the dial plan.
1.615 +; "core show functions" will list all dialplan functions
1.616 +; "core show function <COMMAND>" will show you more information about
1.617 +; one function. Remember that function names are UPPER CASE.
