OpenPKG Specs / file revision

 ; Radio Repeater / Remote Base configuration file (for use with app_rpt)

 ; As of app_rpt version 0.39, 12/20/2005

 ;

 ;[000]					; Node ID of first repeater

 ;rxchannel = Zap/1			; Rx audio/signalling channel

 ; Note: if you use a unified interface (tx/rx on one channel), only

 ; specify the rxchannel and the txchannel will be assumed from the rxchannel

 ;txchannel = Zap/2			; Tx audio/signalling channel

 ;duplex = 2				; (Optional) set duplex operating mode

 ;; 0 = half duplex (telemetry and courtesy tones do not transmit)

 ;; 1 = semi-half duplex (telemetry and courtesy tones transmit, but not

 ;;    repeated audio

 ;; 2 = normal full-duplex mode (Default)

 ;; 3 = full-duplex mode, without repeated audio from main input source

 ;functions = functions-repeater		; DTMF function list

 ;; specify this for a different function list then local when on link

 ;;link_functions = functions-different	; DTMF function list for link

 ;;phone_functions = functions-phone	; (optional) different functions for 'P' mode

 ;;dphone_functions = functions-dphone	; (optional) different functions for 'D' mode

 ;;nodes = nodes-different		; (optional) different node list

 ;tonezone = us				; use US tones (default)

 ;context = default			; dialing context for phone

 ;callerid = "WB6NIL Repeater" <(213) 555-0123>  ; Callerid for phone calls

 ;idrecording = wb6nil			; id recording

 ;accountcode=RADIO			; account code (optional)

 ;funcchar = *				; function lead-in character (defaults to '*')

 ;endchar = #				; command mode end character (defaults to '#')

 ;;nobusyout=yes				; (optional) Do not busy-out reverse-patch when

 					; normal patch in use

 ;hangtime=1000				; squelch tail hang time (in ms) (optional)

 ;totime=100000				; transmit time-out time (in ms) (optional)

 ;idtime=30000				; id interval time (in ms) (optional)

 ;politeid=30000				; time in milliseconds before ID timer

 					; expires to try and ID in the tail.

 					; (optional, default is 30000).

 ;idtalkover=|iwb6nil/rpt		; Talkover ID (optional) default is none

 ;unlinkedct=ct2				; unlinked courtesy tone (optional) default is none

 ;; The tailmessagetime,tailsquashedtime, and tailmessages need to be set

 ;; to support tail messages. They can be omitted otherwise.

 ;tailmessagetime=300000			; Play a tail message every 5 mins

 ;tailsquashedtime=30000			; If squashed by another user,

 ;;					  try again after 30 seconds

 ;tailmessages=msg1,msg2,msg3		;list of messages to be played for tail message

 ; The default values for hangtime, time-out time, and id interval time are

 ; 5 seconds (5000 ms),  3 minutes (180000 ms), and 5 minutes (300000 ms)

 ; respectively

 ;[001]					; Node ID of first repeater

 ;rxchannel = Zap/3			; Rx audio/signalling channel

 ; Note: if you use a unified interface (tx/rx on one channel), only

 ; specify the rxchannel and the txchannel will be assumed from the rxchannel

 ;txchannel = Zap/4			; Tx audio/signalling channel

 ;functions = functions-repeater		; DTMF function list

 ;; specify this for a different function list then local when on link

 ;;link_functions = functions-different	; DTMF function list for link

 ;;phone_functions = functions-phone	; (optional) different functions for 'P' mode

 ;;dphone_functions = functions-dphone	; (optional) different functions for 'D' mode

 ;;nodes = nodes-different		; (optional) different node list

 ;tonezone = us				; use US tones (default)

 ;context = default			; dialing context for phone

 ;callerid = "WB6NIL Repeater" <(213) 555-0123>  ; Callerid for phone calls

 ;idrecording = wb6nil			; id recording

 ;accountcode=RADIO			; account code (optional)

 ;funcchar = *				; function lead-in character (defaults to '*')

 ;endchar = #				; command mode end character (defaults to '#')

 ;;nobusyout=yes				; (optional) Do not busy-out reverse-patch when

 					; normal patch in use

 ;hangtime=1000				; squelch tail hang time (in ms) (optional)

 ;totime=100000				; transmit time-out time (in ms) (optional)

 ;idtime=30000				; id interval time (in ms) (optional)

 ;politeid=30000				; time in milliseconds before ID timer

 					; expires to try and ID in the tail.

 					; (optional, default is 30000).

 ;idtalkover=|iwb6nil/rpt		; Talkover ID (optional) default is none

 ;unlinkedct=ct2				; unlinked courtesy tone (optional) default is none

 ;[002]					; Node ID of remote base

 ;rxchannel = Zap/5			; Rx audio/signalling channel

 ; Note: if you use a unified interface (tx/rx on one channel), only

 ; specify the rxchannel and the txchannel will be assumed from the rxchannel

 ;txchannel = Zap/6			; Tx audio/signalling channel

 ;functions = functions-remote

 ;remote = ft897				; Set remote=y for dumb remote or 

 					; remote=ft897 for Yaesu FT-897 or

 					; remote=rbi for Doug Hall RBI1

 ;iobase = 0x378				; Specify IO port for parallel port (optional)

 ;[functions-repeater]

 ;1=ilink,1				; Specific link disconnect

 ;2=ilink,2				; Specific Link connect -  monitor only

 ;3=ilink,3				; Specific Link connect - transceive

 ;4=ilink,4				; Enter command mode on a specific link

 ;7=ilink,5				; Link status

 ;;XX=ilink,6				; Disconnect all links (not used here)

 ;80=status,1				; System info

 ;81=status,2				; Time

 ;82=status,3				; app_rpt.c Version

 ;6=autopatchup				; Autopatch up

 ;0=autopatchdn				; Autopatch down

 ;90=cop,1				; System warm boot 

 ;91=cop,2				; System enable

 ;92=cop,3				; System disable

 ;[functions-remote]

 ;0=remote,1				; Retrieve Memory

 ;1=remote,2				; Set freq.

 ;2=remote,3				; Set Rx PL tone.

 ;40=remote,100				; Rx PL off

 ;41=remote,101				; Rx PL on

 ;42=remote,102				; Tx PL off

 ;43=remote,103				; Tx PL on

 ;44=remote,104				; Low Pwr

 ;45=remote,105				; Med Pwr

 ;46=remote,106				; Hi Pwr

 ;5=remote,5				; Status

 ;[telemetry]

 ; Telemetry entries are shared across all repeaters

 ; Can be a tone sequence, morse string, or a file

 ;

 ; |t - Tone escape sequence

 ;

 ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

 ; Single frequencies are created by setting freq1 or freq2 to zero.

 ;

 ; |m - Morse escape sequence

 ; 

 ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

 ; [morse] section.

 ;

 ; Follow with an alphanumeric string

 ;

 ; |i - Morse ID escape sequence

 ;

 ; Sends Morse code at the ID amplitude and ID frequency as defined in the

 ; [morse] section.

 ;

 ; Follow with an alphanumeric string

 ;ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)

 ;ct2=|t(660,880,150,2048)  

 ;ct3=|t(440,0,150,2048) 

 ;ct4=|t(550,0,150,2048)

 ;ct5=|t(660,0,150,2048)

 ;ct6=|t(880,0,150,2048)

 ;ct7=|t(660,440,150,2048)

 ;ct8=|t(700,1100,150,2048)

 ;remotetx=|t(2000,0,75,2048)(0,0,75,0)(1600,0,75,2048); 

 ;remotemon=|t(1600,0,75,2048) 

 ;cmdmode=|t(900,903,200,2048)

 ;functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

 ;[morse]

 ;speed=20		; Approximate speed in WPM

 ;frequency=800		; Morse Telemetry Frequency

 ;amplitude=4096		; Morse Telemetry Amplitude

 ;idfrequency=330		; Morse ID Frequency	

 ;idamplitude=2048	; Morse ID Amplitude

 ;[nodes]

 ;000 = context_A@foo.bar.com/1234,foo.bar.com

 ;001 = context_B@baz.waldo.com/4321,baz.waldo.com

 ;002 = context_C@pepper.salt.com/5678,pepper.salt.com,y  ; this is a remote

 ;of course, you can also specify these with domain names, but why rely

 ;on DNS working unnecessarily?

 ;[memory]

 ;; this example gives you 146.460, simplex, 100.0 HZ PL, hi-power, transmit PL

 ;00 = 146.460,100.0,sht

 ;; this example gives you 146.940, minus offset, 100.0 HZ PL, low-power, no PL

 ;01 = 146.940,100.0,-l

 ; The format for these entries is:  Receive-Freq,Receive-PL,Attrbutes

 ;     Attributes: l=low power, m=medium power, h=high power, -=minus offset,

 ;	s=simplex, +=plus offset, t=tx PL enable, r=rx PL enable