OpenPKG Specs: asterisk/zapata.conf@f29abea29121 (annotated)

asterisk/zapata.conf@f29abea29121 (annotated)

asterisk/zapata.conf

Mon, 27 Apr 2009 12:19:05 +0200

author: Michael Schloh von Bennewitz <michael@schloh.com>
date: Mon, 27 Apr 2009 12:19:05 +0200
changeset 202: f29abea29121
permissions: -rw-r--r--

Import new package spec for introduction into repository.

 ;
 ; Zapata telephony interface
 ;
 ; Configuration file
 ;
 ; You need to restart Asterisk to re-configure the Zap channel
 ; CLI> reload chan_zap.so
 ;		will reload the configuration file,
 ;		but not all configuration options are
 ; 		re-configured during a reload.
 ;[trunkgroups]
 ;
 ; Trunk groups are used for NFAS or GR-303 connections.
 ;
 ; Group: Defines a trunk group.
 ;        trunkgroup => <trunkgroup>,<dchannel>[,<backup1>...]
 ;
 ;        trunkgroup  is the numerical trunk group to create
 ;        dchannel    is the zap channel which will have the
 ;                    d-channel for the trunk.
 ;        backup1     is an optional list of backup d-channels.
 ;
 ;trunkgroup => 1,24,48
 ;trunkgroup => 1,24
 ;
 ; Spanmap: Associates a span with a trunk group
 ;        spanmap => <zapspan>,<trunkgroup>[,<logicalspan>]
 ;
 ;        zapspan     is the zap span number to associate
 ;        trunkgroup  is the trunkgroup (specified above) for the mapping
 ;        logicalspan is the logical span number within the trunk group to use.
 ;                    if unspecified, no logical span number is used.
 ;
 ;spanmap => 1,1,1
 ;spanmap => 2,1,2
 ;spanmap => 3,1,3
 ;spanmap => 4,1,4
 ;[channels]
 ;
 ; Default language
 ;
 ;language=en
 ;
 ; Default context
 ;
 ;context=default
 ;
 ; Switchtype:  Only used for PRI.
 ;
 ; national:	  National ISDN 2 (default)
 ; dms100:	  Nortel DMS100
 ; 4ess:           AT&T 4ESS
 ; 5ess:	          Lucent 5ESS
 ; euroisdn:       EuroISDN
 ; ni1:            Old National ISDN 1
 ; qsig:           Q.SIG
 ;
 ;switchtype=national
 ;
 ; Some switches (AT&T especially) require network specific facility IE
 ; supported values are currently 'none', 'sdn', 'megacom', 'tollfreemegacom', 'accunet'
 ;
 ;nsf=none
 ;
 ; PRI Dialplan:  Only RARELY used for PRI.
 ;
 ; unknown:        Unknown
 ; private:        Private ISDN
 ; local:          Local ISDN
 ; national:	  National ISDN
 ; international:  International ISDN
 ; dynamic:	  Dynamically selects the appropriate dialplan
 ;
 ;pridialplan=national
 ;
 ; PRI Local Dialplan:  Only RARELY used for PRI (sets the calling number's numbering plan)
 ;
 ; unknown:        Unknown
 ; private:        Private ISDN
 ; local:          Local ISDN
 ; national:	  National ISDN
 ; international:  International ISDN
 ; dynamic:	  Dynamically selects the appropriate dialplan
 ;
 ;prilocaldialplan=national
 ;
 ; PRI callerid prefixes based on the given TON/NPI (dialplan)
 ; This is especially needed for euroisdn E1-PRIs
 ;
 ; sample 1 for Germany
 ;internationalprefix = 00
 ;nationalprefix = 0
 ;localprefix = 0711
 ;privateprefix = 07115678
 ;unknownprefix =
 ;
 ; sample 2 for Germany
 ;internationalprefix = +
 ;nationalprefix = +49
 ;localprefix = +49711
 ;privateprefix = +497115678
 ;unknownprefix =
 ;
 ; PRI resetinterval: sets the time in seconds between restart of unused
 ; channels, defaults to 3600; minimum 60 seconds.  Some PBXs don't like
 ; channel restarts. so set the interval to a very long interval e.g. 100000000
 ; or 'never' to disable *entirely*.
 ;
 ;resetinterval = 3600
 ;
 ; Overlap dialing mode (sending overlap digits)
 ;
 ;overlapdial=yes
 ;
 ; PRI Out of band indications.
 ; Enable this to report Busy and Congestion on a PRI using out-of-band
 ; notification. Inband indication, as used by Asterisk doesn't seem to work
 ; with all telcos.
 ;
 ; outofband:      Signal Busy/Congestion out of band with RELEASE/DISCONNECT
 ; inband:         Signal Busy/Congestion using in-band tones
 ;
 ; priindication = outofband
 ;
 ; If you need to override the existing channels selection routine and force all
 ; PRI channels to be marked as exclusively selected, set this to yes.
 ; priexclusive = yes
 ;
 ; ISDN Timers
 ; All of the ISDN timers and counters that are used are configurable.  Specify
 ; the timer name, and its value (in ms for timers).
 ; K:    Layer 2 max number of outstanding unacknowledged I frames (default 7)
 ; N200: Layer 2 max number of retransmissions of a frame (default 3)
 ; T200: Layer 2 max time before retransmission of a frame (default 1000 ms)
 ; T203: Layer 2 max time without frames being exchanged (default 10000 ms)
 ; T305: Wait for DISCONNECT acknowledge (default 30000 ms)
 ; T308: Wait for RELEASE acknowledge (default 4000 ms)
 ; T309: Maintain active calls on Layer 2 disconnection (default -1, Asterisk clears calls)
 ;       EuroISDN: 6000 to 12000 ms, according to (N200 + 1) x T200 + 2s
 ;       May vary in other ISDN standards (Q.931 1993 : 90000 ms)
 ; T313: Wait for CONNECT acknowledge, CPE side only (default 3000 ms)
 ;
 ; pritimer => t200,1000
 ; pritimer => t313,4000
 ;
 ; To enable transmission of facility-based ISDN supplementary services (such
 ; as caller name from CPE over facility), enable this option.
 ; facilityenable = yes
 ;
 ;
 ; Signalling method (default is fxs).  Valid values:
 ; em:             E & M
 ; em_w:           E & M Wink
 ; featd:          Feature Group D (The fake, Adtran style, DTMF)
 ; featdmf:        Feature Group D (The real thing, MF (domestic, US))
 ; featdmf_ta:     Feature Group D (The real thing, MF (domestic, US)) through
 ;                 a Tandem Access point
 ; featb:          Feature Group B (MF (domestic, US))
 ; fgccama	  Feature Group C-CAMA (DP DNIS, MF ANI)
 ; fgccamamf	  Feature Group C-CAMA MF (MF DNIS, MF ANI)
 ; fxs_ls:         FXS (Loop Start)
 ; fxs_gs:         FXS (Ground Start)
 ; fxs_ks:         FXS (Kewl Start)
 ; fxo_ls:         FXO (Loop Start)
 ; fxo_gs:         FXO (Ground Start)
 ; fxo_ks:         FXO (Kewl Start)
 ; pri_cpe:        PRI signalling, CPE side
 ; pri_net:        PRI signalling, Network side
 ; gr303fxoks_net: GR-303 Signalling, FXO Loopstart, Network side
 ; gr303fxsks_cpe: GR-303 Signalling, FXS Loopstart, CPE side
 ; sf:	          SF (Inband Tone) Signalling
 ; sf_w:	          SF Wink
 ; sf_featd:       SF Feature Group D (The fake, Adtran style, DTMF)
 ; sf_featdmf:     SF Feature Group D (The real thing, MF (domestic, US))
 ; sf_featb:       SF Feature Group B (MF (domestic, US))
 ; e911:           E911 (MF) style signalling
 ;
 ; The following are used for Radio interfaces:
 ; fxs_rx:         Receive audio/COR on an FXS kewlstart interface (FXO at the
 ;                 channel bank)
 ; fxs_tx:         Transmit audio/PTT on an FXS loopstart interface (FXO at the
 ;                 channel bank)
 ; fxo_rx:         Receive audio/COR on an FXO loopstart interface (FXS at the
 ;                 channel bank)
 ; fxo_tx:         Transmit audio/PTT on an FXO groundstart interface (FXS at
 ;                 the channel bank)
 ; em_rx:          Receive audio/COR on an E&M interface (1-way)
 ; em_tx:          Transmit audio/PTT on an E&M interface (1-way)
 ; em_txrx:        Receive audio/COR AND Transmit audio/PTT on an E&M interface
 ;                 (2-way)
 ; em_rxtx:        Same as em_txrx (for our dyslexic friends)
 ; sf_rx:          Receive audio/COR on an SF interface (1-way)
 ; sf_tx:          Transmit audio/PTT on an SF interface (1-way)
 ; sf_txrx:        Receive audio/COR AND Transmit audio/PTT on an SF interface
 ;                 (2-way)
 ; sf_rxtx:        Same as sf_txrx (for our dyslexic friends)
 ;
 ;signalling=fxo_ls
 ;
 ; If you have an outbound signalling format that is different from format
 ; specified above (but compatible), you can specify outbound signalling format,
 ; (see below). The 'signalling' format specified will be the inbound signalling
 ; format. If you only specify 'signalling', then it will be the format for
 ; both inbound and outbound.
 ;
 ; signalling=featdmf
 ; outsignalling=featb
 ;
 ; For Feature Group D Tandem access, to set the default CIC and OZZ use these
 ; parameters:
 ;defaultozz=0000
 ;defaultcic=303
 ;
 ; A variety of timing parameters can be specified as well
 ; Including:
 ;    prewink:     Pre-wink time (default 50ms)
 ;    preflash:    Pre-flash time (default 50ms)
 ;    wink:        Wink time (default 150ms)
 ;    flash:       Flash time (default 750ms)
 ;    start:       Start time (default 1500ms)
 ;    rxwink:      Receiver wink time (default 300ms)
 ;    rxflash:     Receiver flashtime (default 1250ms)
 ;    debounce:    Debounce timing (default 600ms)
 ;
 ;rxwink=300		; Atlas seems to use long (250ms) winks
 ;
 ; How long generated tones (DTMF and MF) will be played on the channel
 ; (in milliseconds)
 ;toneduration=100
 ;
 ; Whether or not to do distinctive ring detection on FXO lines
 ;
 ;usedistinctiveringdetection=yes
 ;distinctiveringaftercid=yes	; enable dring detection after callerid for those countries like Australia
 				; where the ring cadence is changed *after* the callerid spill.
 ;
 ; Whether or not to use caller ID
 ;
 ;usecallerid=yes
 ;
 ; Type of caller ID signalling in use
 ;     bell     = bell202 as used in US
 ;     v23      = v23 as used in the UK
 ;     v23_jp   = v23 as used in Japan
 ;     dtmf     = DTMF as used in Denmark, Sweden and Netherlands
 ;     smdi     = Use SMDI for callerid.  Requires SMDI to be enabled (usesmdi).
 ;
 ;cidsignalling=bell
 ;
 ; What signals the start of caller ID
 ;     ring     = a ring signals the start
 ;     polarity = polarity reversal signals the start
 ;
 ;cidstart=ring
 ;
 ; Whether or not to hide outgoing caller ID (Override with *67 or *82)
 ;
 ;hidecallerid=no
 ;
 ; Whether or not to enable call waiting on internal extensions
 ; With this set to 'yes', busy extensions will hear the call-waiting
 ; tone, and can use hook-flash to switch between callers. The Dial()
 ; app will not return the "BUSY" result for extensions.
 ;
 ;callwaiting=yes
 ;
 ; Whether or not restrict outgoing caller ID (will be sent as ANI only, not
 ; available for the user)
 ; Mostly use with FXS ports
 ;
 ;restrictcid=no
 ;
 ; Whether or not use the caller ID presentation for the outgoing call that the
 ; calling switch is sending.
 ; See README.callingpres
 ;
 ;usecallingpres=yes
 ;
 ; Some countries (UK) have ring tones with different ring tones (ring-ring),
 ; which means the callerid needs to be set later on, and not just after
 ; the first ring, as per the default.
 ;
 ;sendcalleridafter=1
 ;
 ;
 ; Support Caller*ID on Call Waiting
 ;
 ;callwaitingcallerid=yes
 ;
 ; Support three-way calling
 ;
 ;threewaycalling=yes
 ;
 ; Support flash-hook call transfer (requires three way calling)
 ; Also enables call parking (overrides the 'canpark' parameter)
 ;
 ;transfer=yes
 ;
 ; Allow call parking
 ; ('canpark=no' is overridden by 'transfer=yes')
 ;
 ;canpark=yes
 ;
 ; Support call forward variable
 ;
 ;cancallforward=yes
 ;
 ; Whether or not to support Call Return (*69)
 ;
 ;callreturn=yes
 ;
 ; Stutter dialtone support: If a mailbox is specified without a voicemail
 ; context, then when voicemail is received in a mailbox in the default
 ; voicemail context in voicemail.conf, taking the phone off hook will cause a
 ; stutter dialtone instead of a normal one.
 ;
 ; If a mailbox is specified *with* a voicemail context, the same will result
 ; if voicemail received in mailbox in the specified voicemail context.
 ;
 ; for default voicemail context, the example below is fine:
 ;
 ;mailbox=1234
 ;
 ; for any other voicemail context, the following will produce the stutter tone:
 ;
 ;mailbox=1234@context
 ;
 ; Enable echo cancellation
 ; Use either "yes", "no", or a power of two from 32 to 256 if you wish to
 ; actually set the number of taps of cancellation.
 ;
 ; Note that when setting the number of taps, the number 256 does not translate
 ; to 256 ms of echo cancellation.  echocancel=256 means 256 / 8 = 32 ms.
 ;
 ; Note that if any of your Zaptel cards have hardware echo cancellers,
 ; then this setting only turns them on and off; numeric settings will
 ; be treated as "yes". There are no special settings required for
 ; hardware echo cancellers; when present and enabled in their kernel
 ; modules, they take precedence over the software echo canceller compiled
 ; into Zaptel automatically.
 ;
 ;echocancel=yes
 ;
 ; Generally, it is not necessary (and in fact undesirable) to echo cancel when
 ; the circuit path is entirely TDM.  You may, however, change this behavior
 ; by enabling the echo cancel during pure TDM bridging below.
 ;
 ;echocancelwhenbridged=yes
 ;
 ; In some cases, the echo canceller doesn't train quickly enough and there
 ; is echo at the beginning of the call.  Enabling echo training will cause
 ; asterisk to briefly mute the channel, send an impulse, and use the impulse
 ; response to pre-train the echo canceller so it can start out with a much
 ; closer idea of the actual echo.  Value may be "yes", "no", or a number of
 ; milliseconds to delay before training (default = 400)
 ;
 ; WARNING:  In some cases this option can make echo worse!  If you are
 ; trying to debug an echo problem, it is worth checking to see if your echo
 ; is better with the option set to yes or no.  Use whatever setting gives
 ; the best results.
 ;
 ; Note that these parameters do not apply to hardware echo cancellers.
 ;
 ;echotraining=yes
 ;echotraining=800
 ;
 ; If you are having trouble with DTMF detection, you can relax the DTMF
 ; detection parameters.  Relaxing them may make the DTMF detector more likely
 ; to have "talkoff" where DTMF is detected when it shouldn't be.
 ;
 ;relaxdtmf=yes
 ;
 ; You may also set the default receive and transmit gains (in dB)
 ;
 ;rxgain=0.0
 ;txgain=0.0
 ;
 ; Logical groups can be assigned to allow outgoing rollover.  Groups range
 ; from 0 to 63, and multiple groups can be specified.
 ;
 ;group=1
 ;
 ; Ring groups (a.k.a. call groups) and pickup groups.  If a phone is ringing
 ; and it is a member of a group which is one of your pickup groups, then
 ; you can answer it by picking up and dialling *8#.  For simple offices, just
 ; make these both the same.  Groups range from 0 to 63.
 ;
 ;callgroup=1
 ;pickupgroup=1
 ;
 ; Specify whether the channel should be answered immediately or if the simple
 ; switch should provide dialtone, read digits, etc.
 ; Note: If immediate=yes the dialplan execution will always start at extension
 ; 's' priority 1 regardless of the dialed number!
 ;
 ;immediate=no
 ;
 ; Specify whether flash-hook transfers to 'busy' channels should complete or
 ; return to the caller performing the transfer (default is yes).
 ;
 ;transfertobusy=no
 ;
 ; CallerID can be set to "asreceived" or a specific number if you want to
 ; override it.  Note that "asreceived" only applies to trunk interfaces.
 ;
 ;callerid=2564286000
 ;
 ; AMA flags affects the recording of Call Detail Records.  If specified
 ; it may be 'default', 'omit', 'billing', or 'documentation'.
 ;
 ;amaflags=default
 ;
 ; Channels may be associated with an account code to ease
 ; billing
 ;
 ;accountcode=lss0101
 ;
 ; ADSI (Analog Display Services Interface) can be enabled on a per-channel
 ; basis if you have (or may have) ADSI compatible CPE equipment
 ;
 ;adsi=yes
 ;
 ; SMDI (Simplified Message Desk Interface) can be enabled on a per-channel
 ; basis if you would like that channel to behave like an SMDI message desk.
 ; The SMDI port specified should have already been defined in smdi.conf.  The
 ; default port is /dev/ttyS0.
 ;
 ;usesmdi=yes
 ;smdiport=/dev/ttyS0
 ;
 ; On trunk interfaces (FXS) and E&M interfaces (E&M, Wink, Feature Group D
 ; etc, it can be useful to perform busy detection either in an effort to
 ; detect hangup or for detecting busies.  This enables listening for
 ; the beep-beep busy pattern.
 ;
 ;busydetect=yes
 ;
 ; If busydetect is enabled, it is also possible to specify how many busy tones
 ; to wait for before hanging up.  The default is 4, but better results can be
 ; achieved if set to 6 or even 8.  Mind that the higher the number, the more
 ; time that will be needed to hangup a channel, but lowers the probability
 ; that you will get random hangups.
 ;
 ;busycount=4
 ;
 ; If busydetect is enabled, it is also possible to specify the cadence of your
 ; busy signal.  In many countries, it is 500msec on, 500msec off.  Without
 ; busypattern specified, we'll accept any regular sound-silence pattern that
 ; repeats <busycount> times as a busy signal.  If you specify busypattern,
 ; then we'll further check the length of the sound (tone) and silence, which
 ; will further reduce the chance of a false positive.
 ;
 ;busypattern=500,500
 ;
 ; NOTE: In the Asterisk Makefile you'll find further options to tweak the busy
 ; detector.  If your country has a busy tone with the same length tone and
 ; silence (as many countries do), consider defining the
 ; -DBUSYDETECT_COMPARE_TONE_AND_SILENCE option.
 ;
 ; Use a polarity reversal to mark when a outgoing call is answered by the
 ; remote party.
 ;
 ;answeronpolarityswitch=yes
 ;
 ; In some countries, a polarity reversal is used to signal the disconnect of a
 ; phone line.  If the hanguponpolarityswitch option is selected, the call will
 ; be considered "hung up" on a polarity reversal.
 ;
 ;hanguponpolarityswitch=yes
 ;
 ; On trunk interfaces (FXS) it can be useful to attempt to follow the progress
 ; of a call through RINGING, BUSY, and ANSWERING.   If turned on, call
 ; progress attempts to determine answer, busy, and ringing on phone lines.
 ; This feature is HIGHLY EXPERIMENTAL and can easily detect false answers,
 ; so don't count on it being very accurate.
 ;
 ; Few zones are supported at the time of this writing, but may be selected
 ; with "progzone"
 ;
 ; This feature can also easily detect false hangups. The symptoms of this is
 ; being disconnected in the middle of a call for no reason.
 ;
 ;callprogress=yes
 ;progzone=us
 ;
 ; FXO (FXS signalled) devices must have a timeout to determine if there was a
 ; hangup before the line was answered.  This value can be tweaked to shorten
 ; how long it takes before Zap considers a non-ringing line to have hungup.
 ;
 ;ringtimeout=8000
 ;
 ; For FXO (FXS signalled) devices, whether to use pulse dial instead of DTMF
 ;
 ;pulsedial=yes
 ;
 ; For fax detection, uncomment one of the following lines.  The default is *OFF*
 ;
 ;faxdetect=both
 ;faxdetect=incoming
 ;faxdetect=outgoing
 ;faxdetect=no
 ;
 ; This option specifies a preference for which music on hold class this channel
 ; should listen to when put on hold if the music class has not been set on the
 ; channel with Set(CHANNEL(musicclass)=whatever) in the dialplan, and the peer
 ; channel putting this one on hold did not suggest a music class.
 ;
 ; If this option is set to "passthrough", then the hold message will always be
 ; passed through as signalling instead of generating hold music locally. This
 ; setting is only valid when used on a channel that uses digital signalling.
 ;
 ; This option may be specified globally, or on a per-user or per-peer basis.
 ;
 ;mohinterpret=default
 ;
 ; This option specifies which music on hold class to suggest to the peer channel
 ; when this channel places the peer on hold. It may be specified globally or on
 ; a per-user or per-peer basis.
 ;
 ;mohsuggest=default
 ;
 ; PRI channels can have an idle extension and a minunused number.  So long as
 ; at least "minunused" channels are idle, chan_zap will try to call "idledial"
 ; on them, and then dump them into the PBX in the "idleext" extension (which
 ; is of the form exten@context).  When channels are needed the "idle" calls
 ; are disconnected (so long as there are at least "minidle" calls still
 ; running, of course) to make more channels available.  The primary use of
 ; this is to create a dynamic service, where idle channels are bundled through
 ; multilink PPP, thus more efficiently utilizing combined voice/data services
 ; than conventional fixed mappings/muxings.
 ;
 ;idledial=6999
 ;idleext=6999@dialout
 ;minunused=2
 ;minidle=1
 ;
 ; Configure jitter buffers in zapata (each one is 20ms, default is 4)
 ;
 ;jitterbuffers=4
 ;
 ;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
 ; jbenable = yes              ; Enables the use of a jitterbuffer on the receiving side of a
                               ; ZAP channel. Defaults to "no". An enabled jitterbuffer will
                               ; be used only if the sending side can create and the receiving
                               ; side can not accept jitter. The ZAP channel can't accept jitter,
                               ; thus an enabled jitterbuffer on the receive ZAP side will always
                               ; be used if the sending side can create jitter.
 ; jbmaxsize = 200             ; Max length of the jitterbuffer in milliseconds.
 ; jbresyncthreshold = 1000    ; Jump in the frame timestamps over which the jitterbuffer is
                               ; resynchronized. Useful to improve the quality of the voice, with
                               ; big jumps in/broken timestamps, usually sent from exotic devices
                               ; and programs. Defaults to 1000.
 ; jbimpl = fixed              ; Jitterbuffer implementation, used on the receiving side of a ZAP
                               ; channel. Two implementations are currently available - "fixed"
                               ; (with size always equals to jbmax-size) and "adaptive" (with
                               ; variable size, actually the new jb of IAX2). Defaults to fixed.
 ; jblog = no                  ; Enables jitterbuffer frame logging. Defaults to "no".
 ;-----------------------------------------------------------------------------------
 ;
 ; You can define your own custom ring cadences here.  You can define up to 8
 ; pairs.  If the silence is negative, it indicates where the callerid spill is
 ; to be placed.  Also, if you define any custom cadences, the default cadences
 ; will be turned off.
 ;
 ; Syntax is:  cadence=ring,silence[,ring,silence[...]]
 ;
 ; These are the default cadences:
 ;
 ;cadence=125,125,2000,-4000
 ;cadence=250,250,500,1000,250,250,500,-4000
 ;cadence=125,125,125,125,125,-4000
 ;cadence=1000,500,2500,-5000
 ;
 ; Each channel consists of the channel number or range.  It inherits the
 ; parameters that were specified above its declaration.
 ;
 ; For GR-303, CRV's are created like channels except they must start with the
 ; trunk group followed by a colon, e.g.:
 ;
 ; crv => 1:1
 ; crv => 2:1-2,5-8
 ;
 ;
 ;callerid="Green Phone"<(256) 428-6121>
 ;channel => 1
 ;callerid="Black Phone"<(256) 428-6122>
 ;channel => 2
 ;callerid="CallerID Phone" <(256) 428-6123>
 ;callerid="CallerID Phone" <(630) 372-1564>
 ;callerid="CallerID Phone" <(256) 704-4666>
 ;channel => 3
 ;callerid="Pac Tel Phone" <(256) 428-6124>
 ;channel => 4
 ;callerid="Uniden Dead" <(256) 428-6125>
 ;channel => 5
 ;callerid="Cortelco 2500" <(256) 428-6126>
 ;channel => 6
 ;callerid="Main TA 750" <(256) 428-6127>
 ;channel => 44
 ;
 ; For example, maybe we have some other channels which start out in a
 ; different context and use E & M signalling instead.
 ;
 ;context=remote
 ;sigalling=em
 ;channel => 15
 ;channel => 16
 ;signalling=em_w
 ;
 ; All those in group 0 I'll use for outgoing calls
 ;
 ; Strip most significant digit (9) before sending
 ;
 ;stripmsd=1
 ;callerid=asreceived
 ;group=0
 ;signalling=fxs_ls
 ;channel => 45
 ;signalling=fxo_ls
 ;group=1
 ;callerid="Joe Schmoe" <(256) 428-6131>
 ;channel => 25
 ;callerid="Megan May" <(256) 428-6132>
 ;channel => 26
 ;callerid="Suzy Queue" <(256) 428-6233>
 ;channel => 27
 ;callerid="Larry Moe" <(256) 428-6234>
 ;channel => 28
 ;
 ; Sample PRI (CPE) config:  Specify the switchtype, the signalling as either
 ; pri_cpe or pri_net for CPE or Network termination, and generally you will
 ; want to create a single "group" for all channels of the PRI.
 ;
 ; switchtype = national
 ; signalling = pri_cpe
 ; group = 2
 ; channel => 1-23
 ;
 ;  Used for distinctive ring support for x100p.
 ;  You can see the dringX patterns is to set any one of the dringXcontext fields
 ;  and they will be printed on the console when an inbound call comes in.
 ;
 ;dring1=95,0,0
 ;dring1context=internal1
 ;dring2=325,95,0
 ;dring2context=internal2
 ; If no pattern is matched here is where we go.
 ;context=default
 ;channel => 1

OpenPKG Specs / annotate

asterisk/zapata.conf@f29abea29121 (annotated)

asterisk/zapata.conf